software update
-
- 2.5 Star Member
- Posts: 101
- Joined: Wed Aug 18, 2010 11:07 pm
software update
Can I just download the newer sheetcam and transfer the license or do I need to edit my post processor for floating torch height also. what is the best procedure. FYI I lost all my Toolsets when the computer battery died. Im thinking I may have also lost the correct height setting in the post processor also. I do know what it was but what else is required to revup to a newer version
- djreiswig
- 4.5 Star Elite Contributing Member
- Posts: 2021
- Joined: Thu Nov 19, 2015 10:02 pm
- Location: SE Nebraska
Re: software update
What version do you have? If you have TNG & want to update to the latest version, you can use the update option in the help menu. Your toolset should remain the same. If you edited your post, it should also remain. If you don't have TNG, I don't think your license will work with the newer version.
2014 Bulltear (StarLab) 4x8
C&CNC EtherCut
Mach3, SheetCam, Draftsight
Hypertherm PM65
Oxy/Acetylene Flame Torch
Pneumatic Plate Marker, Ohmic, 10 inch Rotary Chuck (in progress)
C&CNC EtherCut
Mach3, SheetCam, Draftsight
Hypertherm PM65
Oxy/Acetylene Flame Torch
Pneumatic Plate Marker, Ohmic, 10 inch Rotary Chuck (in progress)
-
- 2.5 Star Member
- Posts: 101
- Joined: Wed Aug 18, 2010 11:07 pm
Re: software update
Yes I have TNG 2.06 Les sent me the last release that would work on XP. 6.1.28, the computer is not on the NET so I had to drop the new file on via flash drive.
-
- 2.5 Star Member
- Posts: 101
- Joined: Wed Aug 18, 2010 11:07 pm
Re: software update
Sheetcam, and tool sets all updated!
- ROKCRLER
- 3 Star Elite Contributing Member
- Posts: 646
- Joined: Sun Sep 30, 2018 5:19 pm
-
- 3 Star Member
- Posts: 366
- Joined: Fri Apr 15, 2011 3:47 am
-
- 2.5 Star Member
- Posts: 101
- Joined: Wed Aug 18, 2010 11:07 pm
- ROKCRLER
- 3 Star Elite Contributing Member
- Posts: 646
- Joined: Sun Sep 30, 2018 5:19 pm
-
- 2.5 Star Member
- Posts: 101
- Joined: Wed Aug 18, 2010 11:07 pm
Re: software update
thanks..
- acourtjester
- 6 Star Elite Contributing Member
- Posts: 8131
- Joined: Sat Jun 02, 2012 6:04 pm
- Location: Pensacola, Fla
Re: software update
Rock4Xfab nice looking hole cuts but I think you should work on the lead in/outs of the first image. Maybe change the type of cutting for the inside and outside offset plan.
DIY 4X4 Plasma/Router Table
Hypertherm PM65 Machine Torch
Drag Knife and Scribe
Miller Mig welder
13" metal lathe
Small Mill
Everlast PowerTig 255 EXT
Hypertherm PM65 Machine Torch
Drag Knife and Scribe
Miller Mig welder
13" metal lathe
Small Mill
Everlast PowerTig 255 EXT
-
- 2.5 Star Member
- Posts: 101
- Joined: Wed Aug 18, 2010 11:07 pm
Re: software update
The part was posted out as no offset. I was having an issue with some overlapping contours and Sheetcam was having a fit so I said fuck it just cut. I have since fixed the drawing and it cuts fine. Again this was starting up a machine I built over 14 yrs ago so I am dusting off grey matter and cobwebs remembering all the stuff.
- acourtjester
- 6 Star Elite Contributing Member
- Posts: 8131
- Joined: Sat Jun 02, 2012 6:04 pm
- Location: Pensacola, Fla
Re: software update
Good plan have fun
DIY 4X4 Plasma/Router Table
Hypertherm PM65 Machine Torch
Drag Knife and Scribe
Miller Mig welder
13" metal lathe
Small Mill
Everlast PowerTig 255 EXT
Hypertherm PM65 Machine Torch
Drag Knife and Scribe
Miller Mig welder
13" metal lathe
Small Mill
Everlast PowerTig 255 EXT